 | C.R. LAURENCE DTB3000 CRL Diamond Band Saw
Brand: C.R. Laurence Part Number: DTB3000
Precision Diamond Blade for Glass, Ceramic Tile and Craft Materials A Favorite of Stained Glass Hobbyists The CRL Diamond Band Saw can clean-cut virtually any glass shape, including curves with a radius as small as 1/4 inch (6.4 millimeter). The 36 inch (914.4 millimeter) precision blade is bathed continuously in coolant to prolong life and prevent dust, all the while producing a clean-cut edge that requires little or no finishing. Also cuts tile, ceramics and other brittle craft items. You can stack identical shapes and cut multiple pieces simultaneously. Quiet 110V AC motor has a variable speed (0-2,800 rpm) control, and saw housing is made of rugged aluminum and stainless steel. Max. Glass Thickness: 1/2 in (12.7 mm) Min. Cutting Radius: 1/4 in (6.4 mm) Max. Cutting Radius: 5 in (127 mm) Minimum Order: 1 Each Specifications: Minimum Radius: 1/4 Inch (6.4 millimeter) Maximum Radius: Five Inches (127 millimeters) Cutting Speed: Approximately 26" inches per minute | *$692.52 |
 | C.R. LAURENCE EAF CRL Counter Balance Table Air Flotation System
Brand: C.R. Laurence Part Number: EAF
Easy to Install on any Glass Cutting Table Positions Glass on a Cushion of Air Safely and Easily 110 Volt Electrical Requirement Improve your cutting table by installing air flotation. The CRL Counter Balance Table Air Flotation System is easy to install, and allows you to float, move and easily turn glass on the table top. Contains a self-contained blower system, hose, and 12 check ball outlets. Number of Outlets: 12 Electrical Requirement: 110 Volts F.O.B : Red Oak, TX | *$1,672.67 |
 | C.R. LAURENCE ERB2 CRL Ball Caster for IG Tables
Brand: C.R. Laurence Part Number: ERB2
Will Not Scratch the Glass This spherical CRL Ball Caster is two inches (51 millimeters) in diameter, made of neoprene, and is used on ball caster-type Transfer , Inspection and Tilt tables. The balls will not scratch the glass as it glides over them. | *$13.73 |
 | C.R. LAURENCE ERR1 CRL Stab-In Glass Cutting Table Rollers
Brand: C.R. Laurence Part Number: ERR1
Makes Glass Loading Easy When Table is in Upright Position Easy to Install and Remove CRL ERR1 Stab-In Glass Cutting Table Rollers make an efficient add-on to any tilt-top glass cutting table. The set of four durable rubber rollers mount into steel collars that are recessed into the table's surface. Positioned so they align with your vertical glass storage racks when your table is in the upright position, glass can be easily loaded onto the rollers safely. When the table is then lowered to the horizontal position, the rollers are simply pulled out of the steel collars so you're ready to cut glass. Four each per set. F.O.B : Red Oak, TX | *$1,224.44 |
 | C.R. LAURENCE EW CRL Electric Winch for Glass Cutting Tables
Brand: C.R. Laurence Part Number: EW
Pulls Glass from Vertical Storage Racks onto Tilt-Top Glass Cutting Tables. Provides Safe, Effortless Loading 110 Volt Electrical Power Source The CRL Electric Winch for Glass Cutting Tables takes the strain out of pulling large lites of glass from verical storage racks onto tilt-top cutting tables when they are in the tilt up position. By attaching a CRL Woods Powr-Grip pump type vacuum cup to the winch's cable, the glass is drawn onto the table's wooden or roller toes that have been matched in height to the storage rack floor. The cable is made of strong polyester material so there is no chance of scratching the glass during loading. The CRL Electric Winch for Glass Cutting Tables is powered by your 110 volt electrical system. Voltage Requirement: 110 Volts F.O.B : Red Oak, TX. | *$1,729.74 |
 | C.R. LAURENCE EWV525 CRL Electric Water Valve
Brand: C.R. Laurence Part Number: EWV525
Used on All Model 200 2000 Sanders Makes Sanding Cooler and Faster This CRL Electric Water Valve and Spray Nozzle is used to spray water on belts thus reducing sanding dust and belt wear. The valve can be wired to 110 volt sanders. | *$201.66 |
 | C.R. LAURENCE EZE2001 CRL E-Z Edgerâ„¢ 220 Volt Glass Edging Machine Only
Brand: C.R. Laurence Part Number: EZE2001
An Affordable Alernative to Larger Grinding/Polishing Machines Set-up is Fast and Requires Very Little Operator Training 220 Volt Operation Costs Less to Operate CRL is pleased to present an affordable new edging machine designed to produce satin finished edges on glass up to 1/2 inch (12.7 millimeter) thick. This CRL E-Z Edgerâ„¢ Glass Glass Edging Machine makes simple work of edging 10 to 60 inch (254 to 1,524 millimeter) diameter glass and mirror up to 3/8 inch (9.5 millimeter) thick, and 10 to 44 inch (254 to 1,117 millimeter) diameters for glass up to 1/2 inch (12.7 millimeter) thick. The machine features a 1/2 H.P. motor, adjustable coolant nozzles, and special two wheel gang assembly for profile grinding and finishing without having to change wheels. The CRL EZE2000 Edger measures 30 inches long x 18 inches wide x 12 inches high (762 x 457 x 304 millimeters). Column height is 72 inches (1,828 millimeters) High. Machine Only, does not include wheels. | *$5,201.61 |
| C.R. LAURENCE EZE2K1T CRL E-Z Edgerâ„¢ 110 Volt Glass Edging Machine Kit
Brand: C.R. Laurence Part Number: EZE2K1T
An Affordable Alernative to Larger Grinding/Polishing Machines Set-up is Fast and Requires Very Little Operator Training Kit Includes Machine, Pump and Two Wheels CRL is pleased to present an affordable new edging machine designed to produce satin finished edges on glass up to 1/2 inch (12.7 millimeter) thick. This CRL E-Z Edgerâ„¢ Glass Glass Edging Machine makes simple work of edging 10 to 60 inch (254 to 1,524 millimeter) diameter glass and mirror up to 3/8 inch (9.5 millimeter) thick, and 10 to 44 inch (254 to 1,117 millimeter) diameters for glass up to 1/2 inch (12.7 millimeter) thick. The machine features a 1/2 H.P. motor, adjustable coolant nozzles, and special two wheel gang assembly for profile grinding and finishing without having to change wheels. The CRL EZE2000 Edger measures 30 inches long x 18 inches wide x 12 inches high (762 x 457 x 304 millimeters). Column height is 72 inches (1,828 millimeters) High. Kit Inlcudes: 110 Volt E-Z Edger 110 Volt Submersible Pump 1/4 Inch (6 millimeter) Glass Fine Pencil Edge Wheel 1/4 Inch (6 millimeter) Glass Polishing Wheel Kit Includes Machine, Pump and Two Wheels | *$5,733.86 |
 | C.R. LAURENCE EZE4922M CRL E-Z Edgerâ„¢ 1/4 Medium Grit Pencil Edge Wheel
Brand: C.R. Laurence Part Number: EZE4922M
C.R. LAURENCE EZE4922M CRL E-Z Edgerâ„¢ 1/4 Medium Grit Pencil Edge Wheel. This wheel is used on CRL E-Z Edgers for the grinding of circular glass. The diamonds in this wheel will leave you with a satin finish before polishing. EMCRL Edging Wheels should never be run dry. . | *$385.93 |
 | C.R. LAURENCE EZE942C CRL E-Z Edgerâ„¢ 1/4 Glass Polishing Wheel
Brand: C.R. Laurence Part Number: EZE942C
Used Exclusively for the E-Z Edgerâ„¢ This CRL E-Z Edgerâ„¢ Polishing Wheel is used on CRL E-Z Edger Polishing Machines for the polishing of circular glass. Use CRL Sharpening Stones to remove any type of glaze and to expose fresh diamonds on your wheels. | *$166.42 |
 | C.R. LAURENCE EZE942E CRL E-Z Edgerâ„¢ 3/8 Glass Polishing Wheel
Brand: C.R. Laurence Part Number: EZE942E
C.R. LAURENCE EZE942E CRL E-Z Edgerâ„¢ 3/8 Glass Polishing Wheel. This CRL Glass Polishing Wheel wheel is used on the CRL EZ Edger for polishing glass circles. The wheel material will leave you with a smooth, polished finish. CRL Polishing Wheels should never be run dry. The proper coolant mixture is needed to keep your wheel in optimum operating conditions. This wheel is softer than its diamond counterpart, therefore it will wear faster.. | *$174.87 |
 | C.R. LAURENCE EZE942G CRL E-Z Edgerâ„¢ 1/2 Glass Polishing Wheel
Brand: C.R. Laurence Part Number: EZE942G
C.R. LAURENCE EZE942G CRL E-Z Edgerâ„¢ 1/2 Glass Polishing Wheel. This wheel is used on the CRL E-Z Edger for polishing glass circles. The wheel material will leave you with a smooth polished finish. CRL Polishing Wheels should never be run dry. A proper water/coolant mixture is needed to keep your wheel in optimum operating conditions. This wheel is softer than its diamond counterpart, therefore it will wear faster.. | *$183.76 |
 | C.R. LAURENCE FG14BM CRL 110 Volt FG-14BM Finger Grip Machine
Brand: C.R. Laurence Part Number: FG14BM
Cuts Smooth Finger Pulls in Minutes! This CRL FG-14BM Finger Grip Machine is the most popular machine of its kind. It's ruggedly built and designed for bench use. The machine is easy to use, and allows the operator to cut clean, functional finger pulls in glass, quickly and with confidence. In less than five minutes, you can cut a 2-3/4 inch (69.9 millimeter) long grip, 5/8 inch (15.9 millimeter) wide and 1/8 inch (3.2 millimeter) deep. Volt : 110V | *$1,965.46 |
 | C.R. LAURENCE FP2002 CRL Flat Platen
Brand: C.R. Laurence Part Number: FP2002
Fits Behind Belt Gives Glass a Flat Edge A CRL Flat Platen is used behind the belt to give glass a flat edge. For use on CRL 2200 Series and 100BM Sanders. Must be inserted into a CRL Platen Adapter on older models not equipped with mounting holes. | *$183.44 |
 | C.R. LAURENCE GL4SS CRL Belt Guard Safety Shield for GL4W and CN4106
Brand: C.R. Laurence Part Number: GL4SS
Guards From Flying Debris The CRL Belt Guard Safety Shield fits our model GL4W and CN4106 Belt Sanders. Protects your face and eyes from flying debris, giving you added safety. This is an attachment no shop with a GL4W and CN4106 should be without. Simple installation takes just minutes, and gives you extra protection for the life of your sander. | *$135.68 |
 | C.R. LAURENCE GRA101 CRL Guide Roller Bar Adapter
Brand: C.R. Laurence Part Number: GRA101
Fits on PA100 Platen Adapter Holds Guide Roller Bar GRB102 This CRL Guide Roller Bar Adapter fits into the Platen Adapter and holds the Guide Roller Bar . Special slots for mounting screws allow up and down adjustment for glass thickness. | *$139.70 |
 | C.R. LAURENCE GRB102 CRL Guide Roller Bar for 2200 Series Upright Sanders
Brand: C.R. Laurence Part Number: GRB102
Fits on Roller Bar Adapter GRA101 Allows Easy Lateral Glass Movement The five hard rubber rollers mounted on this CRL Roller Bar facilitate glass edging by allowing easy lateral glass movement. They also help support the total weight of the glass. Bolts to existing CRL 2200 Sanders. Length: 25 in (635 mm) | *$376.54 |
 | C.R. LAURENCE L090 CRL 5/8 to 3/4 Shaft Coupler
Brand: C.R. Laurence Part Number: L090
Used on the Series 200 Upright Sander This CRL 5/8" to 3/4" Shaft Coupler is used on the Series 200 Upright Sander. It is used to adapt the 5/8 inch (16 millimeter) motor shaft to 3/4 inch (19 millimeter) undercut on the one inch (25 millimeter) lower pulley shaft. | *$46.00 |
 | C.R. LAURENCE LCS3084 CRL 360 Degree Rotary Work Table
Brand: C.R. Laurence Part Number: LCS3084
Eliminates Production Steps 2' x 3' (61 cm x 91 cm) Carpeted Surface Holds Units up to 5' x 7' (152 cm x 213 cm) The CRL Rotary Work Table speeds production of Insulating Glass units while creating a safer work place. The glass is held in position by a 6 inch (152 millimeter) vacuum cup on a 2 x 3 foot (61 cm x 91 cm) carpeted surface. Vacuum Cup system is powered by a continuous flow vacuum generator which requires a 35 psi air supply (not supplied) regulated at the table and a 360 degree air driven braking system to stop and hold table in any rotational position. Both the vacuum hold down and braking systems are controlled via tandem foot pedal controls. Swing out support arms expand the top surface to 5 x 7 feet (1,524 x 2,133 millimeters). Work surface height is 36 inches (914 millimeters). Call your CRL Representative or contact us at with additional questions. Always wear the proper protective safety gear including gloves and arm guards when handling glass. | *$2,558.37 |
 | C.R. LAURENCE LN3 CRL Spray Nozzle for Upright Belt Sanders
Brand: C.R. Laurence Part Number: LN3
Used on All Model 200 2000 Sanders Makes Sanding Cooler and Faster This CRL Spray Nozzle for Belt Sanders is used to spray water on belts. Water spray makes sanding cooler and faster, reduces sanding dust and belt wear. | *$48.67 |
 | C.R. LAURENCE PA100 CRL Platen Adapter
Brand: C.R. Laurence Part Number: PA100
Supplied on 2200 Series Upright Sanders Used for Adding Roller, Bar, Flat Platen and or a Guide Roller Bar To add a Bar , Flat or Roller Platen and/or a Guide Roller Bar to a 100BM Sander , you need this part. It's standard equipment on the 2200 and 2200RP sanders. | *$136.87 |
 | C.R. LAURENCE PAE200 CRL Platen Adapter Extension
Brand: C.R. Laurence Part Number: PAE200
Use in Conjunction with PA100 to Create a Double Roller Platen Assembly for 100BM or 2200RP Sanders This CRL Platen Adapter Extension bolts to the top of the Platen Adapter to hold a second roller platen behind belt. | *$163.20 |
 | C.R. LAURENCE PEW31638FE CRL 3/16 -3/8 Flat w/ Seams Diamond Wheel
Brand: C.R. Laurence Part Number: PEW31638FE
For the CRL PE11 Glass Edger This CRL Edging Wheel is made from the finest metal bond diamond composition available. The flat with seams profile gives your glass a finely ground satin finish ready for polishing. This wheel is for use on the CRL Powr Edger . Typical wheel life under optimum operating conditions is 700,000 linear inches (17,780 meters). The wheel is a full seven inches (178 millimeters) in diameter. | *$700.86 |
 | C.R. LAURENCE SM37 CRL Glass Polisher and Scratch Remover Model 37
Brand: C.R. Laurence Part Number: SM37
3/4 HP, Single Phase, 60 Cycle, 120 Volt Motor This CRL Glass Polisher Model 37 is widely used in the glass industry for manual polishing and for the removal of scratches. A polishing compound such as cerium oxide, used on the felt wheel, will also produce a brilliant finish on edges, especially bevels, and will remove hairline scratches while maintaining the surface polish of the glass. The machine is furnished with a solid quality felt wheel, 24 inches O.D. x 18 inches I.D. x 3 inches wide, mounted on a wooden ring, which is V-belt driven by a 3/4HP, single phase, 60 cycle, 120 volt motor. A motor starting switch, truing bar and wooden support shelf are also provided. Height: 48 in (1219.2 mm) Depth: 30 in (762 mm) Width: 20 in (508 mm) | *$4,333.54 |
 | C.R. LAURENCE STT1 CRL Stowaway Glass Cutting Table
Brand: C.R. Laurence Part Number: STT1
A Great Space Saver in the Shop High-Strength Construction Provides Durability Without Excess Weight 500 lb (225 kg) Load Capacity The Stowaway Glass Cutting Table features a generous work surface of 72-1/4 x 96-1/2 inches (1835 x 2450 millimeters) with a rugged, long-lasting felt top designed to reduce vacuum stick when used for cutting glass or other nonporous materials. High-strength construction provides durability without excess weight. Crossed support legs ensure a rigid and stable, 35 inch (889 millimeter) high work surface with a 500 pound (225 kilogram) load capacity. The scissor-action tilt design of the Stowaway floats the pivot point forward as the top lifts, providing nearly effortless manual tilt, without the extra weight of a counter-balanced system. Bronze pivot bushings and nylon washers make movements smooth and quiet. Rubber rollers support glass, laminate or other sheet materials when tilted and flip out of the way when not needed. Fold up the base section, pull back the stabilizing arm and the base is locked into place, ready to stow or roll. With its compact 25-3/4 inch (656 millimeter) deep x 79-3/4 inch (2028 millimeter) high profile, the Stowaway is easy to stow against a wall, roll along narrow aisles, slip through doorways, and fit on freight elevators. Weighing only 337 pounds (153 kilograms), it can even be lifted into the back of a truck for transport to a jobsite. Used as a rack for glass or other sheet materials, the Stowaway can be loaded from the front or from the side. Sheets roll easily and gently across the rubber support rollers. Some assembly required. F.O.B : Laurel, Montana | *$6,166.04 |
 | C.R. LAURENCE VTP1T CRL Panther Instructional Video Tape
Brand: C.R. Laurence Part Number: VTP1T
Full Usage Instructions Shows All the Features of the Panther Edger This videotape depicts the basic unpacking, assembly and operation of the CRL Panther Automatic Diamond Glass Edger . Also shows basic maintenance and the machines limits. It is included when purchasing the CRL Panther Edger . Total of length of video is 46 minutes. | *$25.34 |
 | Capitol Base Units F/Convers Fence Stretcher Bar Only #4SB
Brand: Capitol Base Units F/Convers Part Number: 4SB | *$41.83 |
 | Car Bit - 47706 3/8 Auger Bit
Brand: Irwin Part Number: 47706
######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ############### | *$24.74 |
 | Carry-On 3-Pt. Hitch Hauler, Model# 803
Brand: Carry-On Trailers
Heavy-duty steel hauler is designed with 3-pt. tractor connection for added versatility. Hitch hauler has a 2500-lb. carrying capacity and features a swing-down tailgate. Easy full-body dump. 6ft.W x 4ft.D. Truck ship. U.S.A. Hitch Type: 3 pt, Category Type: 1, Capacity (lbs.): 2,500, Box Size W x D (in.): 6 ft W x 4 Ft D | *$349.99 |
 | CATERPILLAR Track-Type Digger, Model# 513086
Brand: CAT (Caterpillar)
This kid-tough toy provides hours of fun and is built to last for years! Rubberized tracks make it easy to move around the yard or garden, and the oversized seat rotates 360deg as your child works the dual-action handles to dig and scoop. The CAT Track-Type Digger combines a sturdy, high-carbon steel frame with German engineering to create one solid, durable toy. Recommended for ages 3-7. Recommended Use: Ages 3-7, Material: High-carbon steel frame, Weight Capacity (lbs.): 100, Dimensions L x W x H (in.): 39 x 15 1/4 x 16 1/2 | *$159.99 |
 | Cepco Tool PPK-1 Fence Post Pod Kit
Brand: Cepco Tool Model: PPK-1 Part Number: PPK-1
mfr: Cepco Tool Company br• Setting posts by yourselfbr• POST-POD is the ANSWER!br• NO more TIME-CONSUMING bracing !br• NO need for an extra man !br• NO GRIEF ! | *$89.00 |
| | Chain Hoist with 12' of Chain
Brand: CM Part Number: 5605 | *$175.00 |
 | Chain Link Fence U-post Insulator - CHAIN LINK FENCE U-POST INSULATOR
Brand: Red Snap'r Part Number: CX25
Chain Link Fence U-post Insulator - *5 in. poly extension springs spread apart to clamp on chain link fence to keep livestock away. *Can also be used on U-posts. *Color - Black.*25 per Bag. Order | *$11.35 |
 | Chicago Heights 5' Steel Studded T-Post (Pack of 5)
Brand: Chicago Part Number: 5'
Durable high carbon rail steel. Large, streamlined anchor plate. 2 coats of green with silver top baked on protective enamel. All posts are green with a white top. 5 post clips included with each post to attach fence. 1.25 lb. per foot. 18'' bury. No. 5': Studded T post No. 5 1 2': Studded T post No. 6': Studded T post No. 6 1 2': Studded T post No. 7': Studded T post No. 8': Studded T post | *$27.45 |
 | Chicago Heights 6-1/2' Steel Studded T-Post (Pack of 5)
Brand: Chicago Part Number: 6-1/2'
Durable high carbon rail steel. Large, streamlined anchor plate. 2 coats of green with silver top baked on protective enamel. All posts are green with a white top. 5 post clips included with each post to attach fence. 1.25 lb. per foot. 18'' bury. No. 5': Studded T post No. 5 1 2': Studded T post No. 6': Studded T post No. 6 1 2': Studded T post No. 7': Studded T post No. 8': Studded T post | *$34.95 |
 | Chicago Heights 7' Steel Studded T-Post (Pack of 5)
Brand: Chicago Part Number: 7'
Durable high carbon rail steel. Large, streamlined anchor plate. 2 coats of green with silver top baked on protective enamel. All posts are green with a white top. 5 post clips included with each post to attach fence. 1.25 lb. per foot. 18'' bury. No. 5': Studded T post No. 5 1 2': Studded T post No. 6': Studded T post No. 6 1 2': Studded T post No. 7': Studded T post No. 8': Studded T post | *$39.95 |
 | Clevis - 1in. Dia, Heat Treated Pin
Brand: Northern Tool Equipment
Totally forged for excellent grain structure without the built-in-stress. Black powder-coated finish. Pins are yellow zinc dichromate plated. U.S.A. | *$14.99 |
| Clevis - 3/4in. Dia, Heat Treated Pin
Brand: Northern Tool Equipment
Totally forged for excellent grain structure without the built-in-stress. Black powder-coated finish. Pins are yellow zinc dichromate plated. | *$12.99 |
| Clevis - 3/8in. Dia, Heat Treated Pin
Brand: Northern Tool Equipment
Totally forged for excellent grain structure without the built-in-stress. Black powder-coated finish. Pins are yellow zinc dichromate plated. U.S.A. | *$2.99 |
| Clevis - 5/8in. Dia, Heat Treated Pin
Brand: Northern Tool Equipment
Totally forged for excellent grain structure without the built-in-stress. Black powder-coated finish. Pins are yellow zinc dichromate plated. | *$4.99 |
| Clevis - 7/16in. Dia, Heat Treated Pin
Brand: Northern Tool Equipment
Totally forged for excellent grain structure without the built-in-stress. Black powder-coated finish. Pins are yellow zinc dichromate plated. U.S.A. | *$2.99 |
 | Cmc Steel - Southern Post 5Ft Green Fence T-Post W/O Clip TP125PGN050
Brand: CMC SOUTHERN POST Model: TP125PGN050 Part Number: TP125PGN050
Designed to make them easier to use and more durable, these new posts feature an angled stud that helps hold the fence against the post. The large anchor plate provides greater holding power. | *$42.99 |
 | Cmc Steel - Southern Post 6 Tpost 1.25 Standard Green N/Clip TP125PGN060
Brand: CMC SOUTHERN POST Model: TP125PGN060 Part Number: TP125PGN060
Designed to make them easier to use and more durable, these new posts feature an angled stud that helps hold the fence against the post. The large anchor plate provides greater holding power. | *$39.99 |
 | Cmc Steel - Southern Post 6Ft 1.33 Orange Tpost Noclip TP133POR060
Brand: CMC SOUTHERN POST Model: 6 FT. Part Number: TP133POR060
Designed to make them easier to use and more durable, these new posts feature an angled stud that helps hold the fence against the post. The large anchor plate provides greater holding power. | *$48.99 |
 | COBRA 88200 POWER DRUM AUGER 20"
Brand: Cobra Model: 88200 Part Number: 88200
POWER DRUM AUGER 20"
Size: 88200
Unclogs bathtubs, toilets and sink drains up to 3"
Sealed, molded, rust proof poly canister
1/4" diameter coiled wire stores inside canister
Can be operated manually or attached to 1/4 or 3/8" single or variable speed drill | *$22.87 |
 | Columbus McKinnon 12368 Wire Stretcher Hoist
Brand: Columbus McKinnon Model: WS161115 Part Number: 12368
Roller bearing. Malleable hoods grips. All steel safety lock. 2 0 x 30" chain. Automotive red finish. No. 12368: No. 44, 3 8" x 16' rope, 4 sheaves, 250 lb. working load limit No. 12369: No. 88, 1 2" x 50' rope, 4 heavy sheaves, 450 lb. working load limit | *$17.80 |
 | Columbus McKinnon 12376 Wire Grip
Brand: Columbus McKinnon Part Number: 12376
Malleable iron. Yellow chromated. Standard #25. | *$7.69 |
 | Columbus McKinnon M1195 Big Orange Wire Handle Hitch Pin
Brand: Columbus McKinnon Part Number: M1195
Hot forged pin. Micro allow steel. Folding wire handle. Easy to grip, easy to attach pull rope. Complete with hairpin lock. Orange painted. No. M1195: 1 2" pin diameter; 3 1 2" useable length, wire handle No. M1200: 5 8" pin diameter, 3 3 4" useable lengt | *$2.69 |
 | Columbus McKinnon M1196E E-Grip Hitch Pin
Brand: C M Chain Model: M1196E Part Number: M1196E
Ergonomic design. Highest strength. Micro allow steel. Hot forged. Thru hardened heat treatment for strength properties. Supplied with hitch pin. Wide ergonomic handle. Big Orange. No. M1196E: 1 2" pin diameter, 3 1 2" useable length No. M1201E: 5 8" pin | *$4.55 |
| Columbus McKinnon M1200 Big Orange Wire Handle Hitch Pin
Brand: Columbus McKinnon Model: M1200 Part Number: M1200
Hot forged pin. Micro allow steel. Folding wire handle. Easy to grip, easy to attach pull rope. Complete with hairpin lock. Orange painted. No. M1195: 1 2" pin diameter; 3 1 2" useable length, wire handle No. M1200: 5 8" pin diameter, 3 3 4" useable lengt | *$3.04 |
